Tagged: 

Viewing 6 posts - 13 through 18 (of 35 total)
  • Author
    Posts
  • Donald Corenman, MD, DC
    Moderator
    Post count: 8660

    I agree that asking some surgeons technique questions could “get you into trouble” but I think these are reasonable questions and any good surgeon should patiently explain why his or her technique is preferable.

    To revise a failed TLIF fusion, the CT images and MRI images are very important. If the “cage” is well implanted and there are no halos around the cage, I think of a good posterolateral fusion with BMP and screw replacement (these screws will almost always be somewhat loose). If the cage is only on one side and there is good room, a TLIF on the opposite side generally does the trick. There are occasions I had to “dig out” the cage to repair a failed TLIF.

    Dr. Corenman

    PLEASE REMEMBER, THIS FORUM IS MEANT TO PROVIDE GENERAL INFORMATION ON SPINE ANATOMY, CONDITIONS AND TREATMENTS. TO GET AN ACCURATE DIAGNOSIS, YOU MUST VISIT A QUALIFIED PROFESSIONAL IN PERSON.
     
    Donald Corenman, MD, DC is a highly-regarded spine surgeon, considered an expert in the area of neck and back pain. Trained as both a Medical Doctor and Doctor of Chiropractic, Dr. Corenman earned academic appointments as Clinical Assistant Professor and Assistant Professor of Orthopaedic Surgery at the University of Colorado Health Sciences Center, and his research on spine surgery and rehabilitation has resulted in the publication of multiple peer-reviewed articles and two books.
    Renee123
    Participant
    Post count: 130

    Thank you. your bedside manner would seem to far exceed most.

    Basically, My surgeon is telling me if MIS TLIF (with no posterolateral fusion) doesn’t fuse that they will bring me back in and do an ALIF. And I doubt if I am in pain that they will move very fast. There is too much risk with all this.

    Can you please tell me what boomerang cage you use and what the measurements are ?

    FYI, most surgeons do not know the answer to this question either, which I believe to be the most important part of the surgery.

    Donald Corenman, MD, DC
    Moderator
    Post count: 8660

    The boomerang cage is about 30mm long and about 10mm wide. The key is the “open spaces” between the PEEK sidewalls. The boomerang has more surface area for bone graft than other cages. This makes the cage more fragile so insertion has to be more meticulous than most. This also means that the cage is more “biologically active” due to the surface area of the bone graft. I place autogenous bone graft mixed with about 1.5-2.0 mg of BMP in front of the cage and then a laver of “Mastergraft” (a synthetic collage/calcium substance) in back of that and then finally the boomerang cage.

    Interesting in that my CT scans at 5 months demonstrate fusion that first occurs at the boomerang cage and then at the BMP in front of the cage. I would have predicted the opposite effect.

    Dr. Corenman

    PLEASE REMEMBER, THIS FORUM IS MEANT TO PROVIDE GENERAL INFORMATION ON SPINE ANATOMY, CONDITIONS AND TREATMENTS. TO GET AN ACCURATE DIAGNOSIS, YOU MUST VISIT A QUALIFIED PROFESSIONAL IN PERSON.
     
    Donald Corenman, MD, DC is a highly-regarded spine surgeon, considered an expert in the area of neck and back pain. Trained as both a Medical Doctor and Doctor of Chiropractic, Dr. Corenman earned academic appointments as Clinical Assistant Professor and Assistant Professor of Orthopaedic Surgery at the University of Colorado Health Sciences Center, and his research on spine surgery and rehabilitation has resulted in the publication of multiple peer-reviewed articles and two books.
    Renee123
    Participant
    Post count: 130

    I have a transitional vertebrae so I believe my spondylolisthesis and fusion would technically be at L4,L5 even though the surgeons are calling it L5,S1.

    If I were to go the route of MIS TLIF, as you said in an earlier post, I would get a facetectomy and the lamina/pars fracture would stay in, correct?

    1.) Would the facetectomy be done at the top of the vertebrae to access to the disc space or at the bottom of disc space (I am assuming this is L5,S1) or both top and bottom ?

    Thank you again.

    Donald Corenman, MD, DC
    Moderator
    Post count: 8660

    The nomenclature for either L4-5 or L5-S1 does not matter as long was the level is identified correctly during surgery. For the MIS technique, typically the facets are removed only on the side of the TLIF approach and the opposite side is left alone. There might be some surgeons who remove part of the opposite side facets and even some who perform a posterolateral fusion at this side.

    To access the disc space in a TLIF, regardless of MIS or minimal midline, the inferior facet on L5 and the superior facet of S1 have to be removed on that side.

    Dr. Corenman

    PLEASE REMEMBER, THIS FORUM IS MEANT TO PROVIDE GENERAL INFORMATION ON SPINE ANATOMY, CONDITIONS AND TREATMENTS. TO GET AN ACCURATE DIAGNOSIS, YOU MUST VISIT A QUALIFIED PROFESSIONAL IN PERSON.
     
    Donald Corenman, MD, DC is a highly-regarded spine surgeon, considered an expert in the area of neck and back pain. Trained as both a Medical Doctor and Doctor of Chiropractic, Dr. Corenman earned academic appointments as Clinical Assistant Professor and Assistant Professor of Orthopaedic Surgery at the University of Colorado Health Sciences Center, and his research on spine surgery and rehabilitation has resulted in the publication of multiple peer-reviewed articles and two books.
    Renee123
    Participant
    Post count: 130

    Forgive my ignorance. With a bilateral
    pars fracture, MIS TLIF

    Is there 1 facet joint to remove to access disc space or two facet joints just on the TLIF side ?

Viewing 6 posts - 13 through 18 (of 35 total)
  • You must be logged in to reply to this topic.