-
AuthorPosts
-
Have you encountered or heard of any cases where a piece of a disc replacement (Prodisc-C) was dislodged posteriorly, pressing against the anterior cord, resulting in neurological symptoms. Specifically muscle atrophy, fasciculation’s, urinary retention, and temperature sensations changes? Pt. was a weight lifter with an abrupt onset of symptoms.
The prodisc C is a device that has two metal bearing surfaces and a sandwiched polymer (plastic) bearing. By your description, the polymer intermediate bearing surface subluxed or dislocated into the spinal canal and compressed the cord causing myelopathy. This has always been a worry of mine with these devices but I have never heard of one causing this problem.
I always was concerned that a competitive athlete would have an injury with a non-constrained ADR (artificial disc replacement) but I always though it might be with an athlete that experiences large potential injury forces such as an NFL football player or a US ski team Downhill member. I would have included in that group test pilot who experience many G’s or would have to eject. I would have thought that a weight lifter would have controlled loads but carefully thinking about it, this might make sense.
I would like to learn more about this case. You are welcome to personally contact me at (970) 476-1100 and asking for Lori Fugate.
Dr. Corenman
PLEASE REMEMBER, THIS FORUM IS MEANT TO PROVIDE GENERAL INFORMATION ON SPINE ANATOMY, CONDITIONS AND TREATMENTS. TO GET AN ACCURATE DIAGNOSIS, YOU MUST VISIT A QUALIFIED PROFESSIONAL IN PERSON.
Donald Corenman, MD, DC is a highly-regarded spine surgeon, considered an expert in the area of neck and back pain. Trained as both a Medical Doctor and Doctor of Chiropractic, Dr. Corenman earned academic appointments as Clinical Assistant Professor and Assistant Professor of Orthopaedic Surgery at the University of Colorado Health Sciences Center, and his research on spine surgery and rehabilitation has resulted in the publication of multiple peer-reviewed articles and two books.Have you had any experience with produsc c at 2 levels yhat crush the vertebrae between them causing the artificial disc to slid in onto the spinal cord?
Have not seen this scenario. This could happen as the difference in materials strength difference between bone and titanium is large (modulus of elasticity) and high loading could theoretically cause this to occur. However, the forces that could cause this could be close to what could cause a fracture in a “normal” neck. If you have any information on this occurrence, I would appreciate a call. (970) 476-1100
Dr. Corenman
PLEASE REMEMBER, THIS FORUM IS MEANT TO PROVIDE GENERAL INFORMATION ON SPINE ANATOMY, CONDITIONS AND TREATMENTS. TO GET AN ACCURATE DIAGNOSIS, YOU MUST VISIT A QUALIFIED PROFESSIONAL IN PERSON.
Donald Corenman, MD, DC is a highly-regarded spine surgeon, considered an expert in the area of neck and back pain. Trained as both a Medical Doctor and Doctor of Chiropractic, Dr. Corenman earned academic appointments as Clinical Assistant Professor and Assistant Professor of Orthopaedic Surgery at the University of Colorado Health Sciences Center, and his research on spine surgery and rehabilitation has resulted in the publication of multiple peer-reviewed articles and two books.It happened to me. Luckily, it was fixed after 2 long, intense surgeries. Unfortunately, no one is interested in hearing my story, even if it means it could save others.
My vertebrae between the 2 produsc c was completely crushed. These are very dangerous devices to be using “off label”.
I have a very remarkable xray of wgat can and will happen.
Dr. Corenman,
In reference to the original question I was able to find a review of Prodics L success that listed the failure of the high density polyethylene insert in a weightlifter. There was very little information, only listing that there was one Podisc L insert failure in a patient lifting heavy weights.
The patient in question had the ProDics C removed. One of the reps took the insert, which has since been destroyed. MRI does not show anything. I contacted an engineer at the company who is looking into what, if anything, would show up on a MRI. The radiologist I spoke with at my hospital was not sure how a fragment of the insert would appear on MRI. Any guidance would be greatly appreciated.
-
AuthorPosts
- You must be logged in to reply to this topic.